Shutter Systems: High-Power Laser Machining

Conoptics manufactures a line of laser accessories for laser modulation, driver electronics, beam deflectors, noise reduction and optical isolators. Conoptics manufactures a complete line of Electro-Optic Modulation Shutter Systems designed to work specifically with High-Power Laser Machining.

Free Product Whitepapers Download Now

  • This field is for validation purposes and should be left unchanged.

Laser Machining is a technology that utilizes a laser to cut materials, and is typically used for industrial manufacturing applications.  Laser cutting works by directing the output of a high-power laser, by computer, at the material to be cut. The material then either, melts, burns, vaporizes away, or is blown away by a jet of gas leaving an edge with a high-quality surface finish.  Conoptics manufactures a complete line of Electro-Optic Modulation Shutter Systems specifically designed to work with High-Power Lasers and Machining applications.

Model 350-80LA-02 Specifications

Aperture 3.5mm
Dimensions 50mm x 137mm
Transmission >90%
Wavelength Range 1064nm
Piezo Resonances Minimal with clamped version (BK Option)
Volts ½ wave at 1064nm 720v
Contrast Ratio 700:1
Driver Compatibility Full modulation with Model 302RM Power Amplifier

Model 302RM Specifications

Cabinet Driver and power supply in singe cabinet
Test Feature Built-in test feature allows testing for max transmission of Pockel-Cell without adjusting bias voltage
Input Impedance Choice of amplifier input impedance by rear panel switch (50ohm/1k ohm)
DC Bias Improved DC biasing of Pockel-Cell provides greater linearity at higher bias voltages
Voltage Range +/- 450VDC controlled by ten-turn front panel pot.  Digital meter monitors differential bias applied to E.O. Modulator
Linearity 10 bits referenced to full scale (.1%)
Bandwidth DC to >200Khz with 90pf load and 3M (RG-62) cables
Max. Output Drive Level 750VP-P into 90pf load
Amplifier Input Signal 2VP-P max into 50/1k ohms delivers 750VP-P out
Input Power (AC) 60W typical.  Input power is both load (modulator) and frequency dependent.
Dimensions 19″ Rack Mountable, 5.25″ H(133mm) (3U) x 14″D (356mm)
Cooling Forced air
Operating Environment Designed for laboratory use (indoor only) Temperature range +5deg C to +50 deg C ambient Humidity 20%-80% RH up to 32deg C Altitude <3000M
Weight 20lbs (9.07kg)

Model 102 Modulator Mount Specifications

Height Adjustment Range: 2.6 inches (6.6cm)
Lowest Center Line 4.15″, 10.5cm
Highest Center Line 6.75″, 17.2cm
Height without Mounting Rings: Fully Retracted Height 2.30″, 5.8cm
Fully Extended Height 4.90″, 12.4cm
Weight 3.33lbs.
Height with Mounting Rings: (Center of Ring) Fully Retracted Height 3.90″, 9.9cm
Fully Extended Height 6.50″, 16.5cm
Weight 3.95lbs.
Dimensions:
(Overall L x W x H)
Fully Retracted w/o Rings 10″L x 3.6″W x 2.3″H
25.4cm x9.1cm x 5.8cm
Fully Extended w/o Rings 10″L x 3.6″W x4.9″H
25.4cm x9.1cm x12.4cm
Fully Retracted with Rings 10″L x 3.6″W x 6.3″H
25.4cm x9.1cm x 16cm
Fully Extended with Rings 10″L x 3.6″W x 8.9″H
25.4cm x9.1cm x 22.6cm
Alignment Tool Option: Diameter is 5cm Aperture 2mm

 

 

Founded 1981

Over 3 Decades of Service

Customer Satisfaction

Consistently Ranked #1

Made in USA

Proudly Made in the USA

Global Representatives

19 Global Partners